Super Street Network

 |   |  2000 Honda S2000 - Budget Friendly
Subscribe to the Free
Newsletter

2000 Honda S2000 - Budget Friendly

The $2,500 canvas that’s worth every penny

Rodrez
Oct 4, 2012
Photographer: Henry Z. DeKuyper
Htup 2012 01 o+2000 honda s2000+AP2 front bumper Photo 1/10   |   HTUP-121000-GOAUTO-054-058

“It had Nissan 300ZX wheels…and an awesome ‘Drift Happens’ sticker on the rear.” Not exactly the ideal groundwork for one of Honda’s flagships, but Greg Carter, owner of Go-Autoworks in Montgomery, Alabama, knows a good thing when he sees it. And while the bruised and battered AP1 had certainly seen better days during its 12 years of service, he was quick to recognize its potential.

A longtime single-cam aficionado, Greg’s build résumé is packed with boosted D-series Civic and CRX screamers, which makes this particular project all the more interesting. “The car was purchased in July 2010, less than two weeks after selling my drag car chassis. I wasn’t even looking for a car as I was taking a break due to just being busy at the shop and a planned wedding,” he recalls. However, plans often change, especially after he spotted the bright yellow roadster perched on a repo lot and familiar thoughts of boost began to entice his senses. A closer look revealed a long list of work required just to get the car up to respectable factory standards, including removing the aforementioned Nissan wheels and embarrassing bumper sticker. Greg adds, “It had obviously been beat on with its torn top, duct taped rear window, beat-up bumpers, busted lights, and caved-in rear quarter. The upside was it had stock suspension, stock exhaust, no bolt-ons and decent interior (under the dirt and mildew).” Negotiations commenced, and $2,500 later, Greg broke his single-cam streak and took ownership of the battered AP1.

Htup 2012 04 o+2000 honda s2000+turbocharger Photo 2/10   |   2000 Honda S2000 - Budget Friendly

The first order of business was repairing the damaged exterior. The car had previously been painted more than once, evident from the layers of paint mixed with Bondo on the rear quarter panel. He stripped the car naked and even rolled the fenders in anticipation of wider wheels prior to handing the chassis off to the body shop. Along with the car itself, a new set of AP2 bumpers, front lip, and VIS hardtop were added to the paint sprayer’s “to-do” list. Almost four months flew by before the car was pulled back into the Go-Autoworks garage sporting a rejuvenated body complete with a fresh slathering of OEM Rio yellow.

Everything inside the cabin, including the factory soft top, was completely removed as Greg put a number of hours into cleaning and reconditioning the long-neglected interior. By this point, even with the car’s investment price and body shop tally, its value went well past the amount of money spent, though Greg is quick to point out, “There’s really no comparison between the cost of an S2000 part and a Civic part.” In reality, the car could have easily been flipped for a considerable profit, but Greg decided to keep the S and began devising a plan for more power. With half a dozen personal turbo projects under his belt and a slew of ecstatic customers, it didn’t take much to sway this shop owner toward the dark side—especially since Go-Autoworks, established in 2002, specializes in turbo kits and associated parts.

“I wanted this car to look good, drive great, and be enjoyable while still competitive in any scenario. I didn’t want it to be trendy.” “Any scenario” would include as much road racing as it would drag racing, so a dyno-busting, peak power number was never the goal. Instead, a well-balanced and reliable performer that could hold its own in any form of motorsport was the blueprint for the project. A PTE turbo and Rev hard cast manifold would serve as the foundation for the initial build-up, utilizing a completely stock motor. At a very tame 8 psi, a thick, usable powerband that peaked at 330 whp was achieved, and Greg was pleased with the results, though he knew the motor was on borrowed time.

Htup 2012 10 o+2000 honda s2000+interior Photo 6/10   |   2000 Honda S2000 - Budget Friendly

“Part of the rough original state included the fact that the car had just one quart of oil in it when I got it! Knowing this, I had already begun looking for new motor parts. I picked up a slight ‘tick’ from the bottom end, and parked the car in preparation for the rebuild.” By the time the original motor began showing signs of decomposition, an AEBS-sleeved block and spare F20 head were already sitting at the shop, begging for active duty. Greg adds, “I knew off the top I wouldn’t use the more popular low-compression piston route. I chose 10.5:1 CPs to keep the compression ratio as close to stock as possible, along with a set of BC H-beam rods.” With all of the essentials ready to roll, Greg paid a visit to his friend Mike at TDC performance for some machine work and final assembly.

Rather than using an off-the-shelf exhaust manifold, Greg built his own sidewinder-style manifold but later decided to swap turbos, and realized the two wouldn’t be compatible. Rather than starting over from scratch and taking away from customer demands, he contacted Brad at AFI Turbo and ordered a sidewinder street-version manifold for the build. Full Blown dual hangers and 340lph pumps would provide the fuel, while an AEM methanol kit lowers inlet temps and fights detonation. The decision to choose between tuning on race gas or street gas presented very little dilemma as Greg explains, “My previous high-horsepower builds were tuned on race gas and became dedicated track cars. I didn’t want that for this car.” The result of careful planning and a solid mix of Go-Autoworks custom parts combined with high-quality goods from industry standouts leaves Greg with absolutely no regrets on his impulse purchase some two years ago.

Htup 2012 05 o+2000 honda s2000+catch can Photo 7/10   |   2000 Honda S2000 - Budget Friendly

The act of rescuing a car from its virtual deathbed and transforming it into something as respectable as Greg Carter’s AP1 is something that can be appreciated by any true gear head—especially those of us working on a budget.

Bolts & Washers

Propulsion
F20C
AEM Series II EMS
AEBS Copper O-ring/sleeved block
Innovative 85A mounts
CP 87.5mm pistons, 10.5:1
Brian Crower rods
Mizu radiator hoses
TDC Performance assembly/machine work
Rev valves
Rev valvesprings
Rev retainers
Go-Autoworks headwork
Garage PWR intake manifold port
Hondata intake manifold gasket
ARP head studs
ARP exhaust manifold studs
Bullseye Power billet batmowheel S362
AFI street sidewinder exhaust manifold
Racecharge piping kit
Go-Autoworks GT600 intercooler
Go-Autoworks V-Band exhaust
Megan muffler
Custom test pipe
TiAL MVR 44mm wastegate
Go-Autoworks wastegate dump tube, recirculated to mid-pipe
TiAL Q blow-off valve
Go-Autoworks turbo blanket
Go-Autoworks oil kit
Go-Autoworks EBC push-lock kit
Skunk2 70mm throttle body
AEM ignition box
K-series coil packs
Go-Autoworks catch can kit
Full Blown dual pump hanger
Dual FB 340lph fuel pumps
ID1000 injectors
Go-Autoworks lines
Go-Autoworks inline fuel filter
AEM fuel pressure regulator
AEM water methanol kit
Competition Clutch Stage 5
Competition Clutch steel flywheel
InlinePro R200 differential kit
HaSport 90A billet differential mounts
Driveshaft Shop Pro axles/hubs
Go-Autoworks stainless clutch line

Htup 2012 03 o+2000 honda s2000+boosted F20C Photo 8/10   |   Once lifeless, this AP1 has a new lease on life in the form of a well-built and boosted F20.

Suspension
Skunk2 Pro C
Cusco subframe brace
Whiteline front lower brace
GP rear tie-bar

Htup 2012 07 o+2000 honda s2000+TiAL wastegate and blowoff valve Photo 9/10   |   2000 Honda S2000 - Budget Friendly

Resistance
All stock

Wheels & Tires
Advanti Vago wheels: 18x8 +43 front, 18x9 +43 rear
Nexxen tires: 225/40-18 front, 255/35-18 rear

Exterior
Rio yellow color change
Body/paintwork by Alfred Jones
VIS hardtop
VIS front lip
OEM AP2 front/rear bumpers
GS rear diffuser

Interior
Schroth 4-pt lock harness, track only
Cusco 4-pt rollbar
Skunk2 shift knob

Props
My family and the crew at Go-Autoworks for the help and support, Mike at TDC, Greg at Innovative Mounts, and Aaron B. at Skunk2

Owner Specs

Daily grind
Owner of Go-Autoworks

Htup 2012 06 o+2000 honda s2000+VIS hardtop Photo 10/10   |   HTUP-121000-GOAUTO-054-058

Favorite sites
go-autoworks.com and d-series.org

Screen name
Go-Autoworks

Building Hondas
13 years

Dream car
Black on black Acura NSX with enough money in the trunk to do what I want with it

Inspiration for this build
Building/owning several high-horsepower D-series Civics

Future builds
That NSX!

Go-Autoworks Doin’ Work

Greg Carter began building cars in the late ’90s and with his hands-on experience, opened the doors to Go-Autoworks in 2002. A move to the current location took place in 2007, and though Greg is the only full-time employee, he assures us he has plenty of help from three part-time coworkers who help tremendously with fab work and installs. Specializing in Honda/Acura turbo kits and related components as well as custom fab work, the Go-Autoworks crew has been responsible for countless builds, from mild street setups to pure drag cars. “My main goal was to build a name that would stand on its own. I want the public to know they’re dealing with top quality, backed by great service and support whenever Go-Autoworks is mentioned. Our turbo kits are based on the needs of all types of enthusiasts, especially the average guy, which is why we offer a variety of kits and options that cover a wide power range without breaking the bank.”

Sources

Skunk2 Racing
Norco, CA 92860
951-808-9888
http://www.skunk2.com
Competition Clutch
Conyers, GA 30012
800-809-6598
http://www.competitionclutch.com
Injector Dynamics
214-607-9022
http://www.injectordynamics.com
Go-Autoworks
334-467-4171
http://www.go-autoworks.com
By Rodrez
530 Articles

BROWSE CARS BY MARKET

MORE FEATURES

What it took to prep the Super Street 2018 Toyota C-HR for the 2017 SEMA Show
Sam DuNov 16, 2017
Preview the January 2018 issue of Super Street, featuring SE*KI Motorsports’ 580HP 180SX; Michael Baghdadi’s Evo VIII; Will Tetro’s 1,100HP FC RX-7; Scotty G’s K20 911; and much more!
Bob HernandezNov 16, 2017
Whether you're into rotary powered vehicles or the more polarizing non-rotary builds, all of these RX-7s are insanely good.
Jofel TolosaNov 16, 2017
Set to arrive in 2020, the Aston Martin Valkyrie AMR Pro receives more power and additional aerodynamic updates compared to the road car.
Kelly PleskotNov 16, 2017
After months of waiting, the fruits of the Singer-Williams matchup finally take shape. The Porsche restorer reveled renderings for the DLS project recently.
Conner GoldenNov 15, 2017
Sponsored Links

SEARCH ARTICLES BY MAKE/MODEL

Search
CLOSE X
BUYER'S GUIDE
SEE THE ALL NEW
NEWS, REVIEWS & SPECS
TO TOP