Super Street Network

 |   |   |  Explained: The Difference Between Lambda and AFR
Subscribe to the Free
Newsletter

Explained: The Difference Between Lambda and AFR

Explaining the Difference Between Two, Valuable, Tuning Tools

Mike Magda
Nov 13, 2017
Photographers: Evan Perkins, Jake Headlee

As performance enthusiasts and racers work with more sophisticated tuning tools—especially those designed for EFI engines—there's a growing debate on whether to use air-fuel ratio or Lambda in the calibrations and dyno testing. Drivers may also have a choice between the two during real-time observation on their gauge.

To be clear, an engine doesn't know the difference between AFR and Lambda. It's simply two different terms that that tuners use to effectively impart the same measurement of air and fuel used in the engine's combustion cycles. However, the vernacular distinction isn't as casual as, say the similarity between "dollar" and "buck." There are distinct advantages to using A/F or Lambda in certain situations.

Lambda vs AFR innovate motorsports ECB 1 gauge Photo 2/13   |   This Innovate Motorsports ECB-1 monitors Lambda, ethanol content and boost. This engine is idling at .97 Lambda, which equates to a near-stoichiometric 14.2 AFR.

SO, WHAT IS LAMBDA?

Lambda, which is a Greek letter demonstrated by the symbol ?, represents all fuel's stoichiometric value as 1.00. Lean conditions would represent a value higher than 1.00, and rich conditions are lower. These lean (higher) and rich (lower) values are calculated for the Lambda scale by dividing the observed A/F ratio with that particular fuel's stoich. For example: a 12.8:1 observed reading with gasoline is divided by 14.7 to produce a 0.87 Lambda reading.

HOW IS LAMBDA CALCULATED?

A wideband sensor calculates lambda by comparing the oxygen left in the exhaust to the sensor's reference pump cell, which is referencing stoich. Because the sensor reads oxygen content, it is impartial to the fuel type being used. If the engine is burning fuel at its specific stoichiometric ratio, all of the oxygen is consumed during combustion. When the sensor detects this stoichiometric condition (no oxygen in the exhaust flow), the lambda gauge will display 1.

Lambda vs AFR oxygen sensor Photo 3/13   |   An Oxygen sensor is actually a Lambda sensor, and an equation is necessary (Lambda reading X stoichiometric ratio for the fuel being measured) in order to calculate AFR.

AIR FUEL RATIO, HORSEPOWER AND STOICHIOMETRY

As most of us learned early in our hot-rod schooling, air-fuel (A/F) ratio is calculated by dividing the pounds of air an engine inhales by the pounds of fuel delivered per hour to the engine. Since the amount of fuel burned by the engine directly correlates to the horsepower produced, that fuel level requires a sufficient amount of air for combustion. In other words, A/F is a tunable property that directly contributes to an engine's power and efficiency.

Perhaps the first big, unpronounceable word we ever encountered in a garage was "stoichiometric." By definition, it's the optimum mixture of air and fuel, and that formula changes for each type of fuel. For pump gasoline, scientists determined that 14.7 parts of Oxygen is needed for one pound of fuel to completely burn to the point where there is no leftover oxygen or fuel—only the normal byproducts of combustion that include water and carbon dioxide.

Lambda vs AFR lambda symbol Photo 4/13   |   Lambda, is a Greek letter demonstrated by the symbol ?, and means a lot of things in differing scientific fields. In engine tuning, it is a ratio between the amount of oxygen actually present in a combustion chamber vs. the amount that should have been present to obtain perfect combustion.

That 14.7:1 ratio is stoichiometric for gasoline, usually shortened to "stoich (pronounced stow-ick) in track slang. If there's less oxygen and more fuel—say a ratio of 12:1—then the mixture is considered rich. If there's more oxygen and less fuel—say a ratio of 16:1—then the mixture is considered lean. Stoich is basically the 50-yard line between rich and lean.

If the fuel carries its own oxygen or the energy content of the fuel changes, then stoich changes. Methanol has one oxygen atom in its formula, so stoic is 6.45:1. That is, it takes just 6.45 parts of air for one pound of fuel to efficiently combust.

Lambda vs AFR air fuel ratio gauge Photo 5/13   |   Lambda Vs AFR Air Fuel Ratio Gauge
Lambda vs AFR air fuel ratio gauge Photo 6/13   |   Lambda and AFR are both indicators of an engine's combustion mixture. However, AFR is dependent on the type of fuel being used, while lambda is not.

Nitromethane, that wonderful hydrocarbon that carries two oxygen atoms, has a stoic of 1.7:1. On the track, a Top Fuel engine may as rich as 1:1, and that's why it needs more than 80 gallons of fuel per minute to keep up with all the air pushed through by the massive 14-71 supercharger running over 60 pounds of boost.

LAMBDA AND ALTERNATIVE FUEL TUNING

Lambda has long been used for tuning purposes in high-end race operations and the OEMs—especially in countries on the metric system. It never really started breaking into the domestic mindset until a new high-performance fuel became readily available at the pump.

Lambda vs AFR e85 Photo 7/13   |   Lambda Vs AFR E85
Lambda vs AFR ethanol fuel Photo 8/13   |   The stoichiometric ratio of E85 is 9.765. However, E85 is rarely the 85% ethanol, 15% gasoline mix it claims to be. For that reason, its stoich can fluctuate considerably. This makes Lambda a better tuning tool because it is not dependent on fuel type or mixture.

The issues with tuning using AFR started when E85 became popular," says Felipe Saez, customer service technical adviser at Innovate Motorsports. "E85 defined as exactly 85 percent ethanol and 15 percent gasoline has a stoichiometric ratio of 9.8:1. The problem is that E85 is rarely an 85/15 exact blend of ethanol and gasoline when you get it at the pump. With every different blend, you must calculate a different stoichiometric ratio."

Unlike methanol that is produced from natural gas, ethanol is produced from corn or other agricultural products. Both carry a single oxygen atom in their chemical makeup. Pure 200-proof ethanol has a 9.0:1 stoich ratio, and when mixed with gasoline to make E85 it has the aforementioned 9.8:1 stoich.

Lambda vs AFR MTX l wideband gauge Photo 9/13   |   This Innovate Motorsports MTX-L wideband gauge is capable of displaying in either AFR or Lambda.

As the benefits and use of E85 became more widespread, not only were the different blends at the pump a problem, but many street enthusiasts switched between gas for cruising and E85 for racing. Calibrating the ECM using A/F or watching the gauge to make sure you didn't lean out the motor became quite confusing and bordering on impractical.

"The solution to this problem is to simply use Lambda as your unit of measure since this does not change, regardless of the fuel or fuel blend being used," advises Saez. "I recommend Lambda be used by anybody who runs E85 or tuners that tune different fuels. At the end of the day, you want to keep things consistent to make interpreting the data as easy as possible.

Lambda vs AFR gas pump Photo 10/13   |   The stoichiometric ratio, or "stoich" in racer jargon, changes from fuel to fuel, depending on its chemical makeup. Gasoline's unique stoich is 14.7.

"When discussing or comparing tunes it is important that the unit of measure being compared be the same," continues Saez. "I remember one scenario where a user was shooting for a 7.6 AFR when he was running in the gasoline scale. The number he was shooting for, was given to him by somebody that had their setup set to AFR in the E85 scale. 7.6 E85 AFR = 11.5 Gasoline AFR = .8 Lambda."

In racing applications, stoich is very rare. Under load, an engine is usually tuned between 15% - 25 % richer than stoichiometric. They will fatten or richen up the fuel mixture to pack a little more energy potential into the engine. Key to observing an accurate fuel mixture is running a quality wide-band O2 sensor mated to a digital gauge, such as the MTX-L Plus from Innovate Motorsports. A wide-band sensor generally reads in Lambda; that is, it's measuring the free air in the spent gasses and calculating the ratio. A factory narrow-band O2 will not work well in performance applications.

Lambda vs AFR VP C9 fuel Photo 11/13   |   Race fuels can have a slightly different stoichiometric ratio due to their altered chemistry. This VP C9 fuel has a stoich of 14.82. Oxygenated race fuels are even more affected.

"A narrowband sensor will not communicate the necessary data a racer is looking for," said Saez. "A narrowband sensor will only read richer or leaner than stoichiometric. A wideband will read the specific values in a much broader range."

"A narrowband reads a narrow range, richer or leaner than stoichiometric," says Saez. "A wideband will read the full spectrum. The Innovate line of widebands allows you to take measurements from .5 to 1.5 lambda. A wideband cannot pinpoint which fuel you are using because it is only reading the oxygen, or lack thereof. A wideband displays AFR by calculating the Lambda value by the stoichiometric ratio selected."

Conventional wisdom suggests that it's a good idea to get comfortable using both, but the most effective course of action is choosing the measurement you're most comfortable with and learn all you can about it "The strategy should be to pick your unit of measure and stick with it. The worst thing a user can do is to use AFR and change the stoichiometric ratio with each fuel type since this will make interpreting the data difficult," urges Saez.

012 lambda vs AFR nitro methane fuel Photo 12/13   |   012 Lambda Vs AFR Nitro Methane Fuel
Lambda vs AFR nitro methane molecular structure Photo 13/13   |   Nitro methane, the fuel of choice of top-fuel dragsters, brings two of its own oxygen molecules to the combustion party. For this reason, its stoichiometric ratio is an extremely low 1.7:1. When a Top Fuel engine is running, the cylinder, at TDC, is almost completely full of fuel.

The fear of Lambda has certainly been moderated with more emphasis on the benefits of E85 in addition to gauges like the MTX-L Plus that can quickly switch between both measurements. "Lambda has not been widely adopted in the United States and therefor it sounds foreign to most," sums up Saez. "With E85 there has been wider adoption."

Sources

Innovate Motorsports
Irvine, CA
714-372-5910
http://www.innovatemotorsports.com
By Mike Magda
1 Articles

BROWSE CARS BY MARKET

MORE HOW TO

Improved handling and a lower stance were welcome additions to the Civic, but now it's time for a new set of wheels and tires,
RodrezNov 8, 2017
S-Tec Motorsports builds a 1,000HP Pro Drift 2JZ-GTE for RAD Dan's Toyota.
Bob HernandezNov 7, 2017
Upgrading to coilovers and stiffer anti-roll bars along with an entire brake system update
Nate HasslerOct 30, 2017
SS's Modified Civic project visits Eibach Springs for new, prototype Pro-Street-S coilovers
RodrezOct 26, 2017
E85 is a wonder-fuel when it comes to boost, but optimizing a turbocharged/supercharged vehicle for it takes special tuning consideration.
Richard FongOct 16, 2017
Sponsored Links

SEARCH ARTICLES BY MAKE/MODEL

Search
CLOSE X
BUYER'S GUIDE
SEE THE ALL NEW
NEWS, REVIEWS & SPECS
TO TOP