COBRA Daytona Sport Seat Install

1. Start off by removing the stock seats. Integras are usually held in with (4) 12mm hex bolts.
1. Start off by removing the stock seats. Integras are usually held in with (4) 12mm hex
2. We had Wedge Engineering fab up a set of their brackets for our Integra. They are made to order based on the brand/model of seat.
2. We had Wedge Engineering fab up a set of their brackets for our Integra. They are mad
3. Lay the bracket down and bolt it in. Be sure to hand-tighten all bolts to ensure alignment. Proceed to torque down to 26 ft-lbs.
3. Lay the bracket down and bolt it in. Be sure to hand-tighten all bolts to ensure align

4. We thought it would be cool to add some sliders to our Cobras to offer stock-like adjustability. The sliders come complete with tabs and the hardware pictured. The tabs allow you to raise or lower the height of the seats. We opted for the lowest setting.
4. We thought it would be cool to add some sliders to our Cobras to offer stock-like adju
5. The spacers come in the slider kit for a reason. Use them. Install one spacer per bolt when attatching the tab to the slider mechanism.
5. The spacers come in the slider kit for a reason. Use them. Install one spacer per bol
6. The bolts are machine-threaded, so just get the first few threads started.

7. It's easier to use an allen key to tighten. Be sure the bolt is as tight as possible. Better yet, learn from our mistake and use a drop of thread-locking compound (blue) on each bolt so they don't back out.
7. It's easier to use an allen key to tighten. Be sure the bolt is as tight as possible.
8. Besides wasting bandwidth, this picture is to make the slider assembly easier. Push down on the hinge to allow the slider to move fore/aft.
8. Besides wasting bandwidth, this picture is to make the slider assembly easier. Push do
9. This will allow you to install the other bolt/washer without having to try and "center" the slider on the tab.
9. This will allow you to install the other bolt/washer without having to try and "center"

10. This is a side view of the slider/tab. Notice that the spacers push the slider up about 5mm, which is huge once you bolt the seats in. Choosing the lower holes on the tabs cancels this out.
10. This is a side view of the slider/tab. Notice that the spacers push the slider up abo
11. This is the trickiest part. The piano wire arm extends across the two sliders allowing them to function in unison. Install one at a time.
11. This is the trickiest part. The piano wire arm extends across the two sliders allowin
12. Slide the washer over the two bends to hold it in place. We know, it looks a little backyard-boogy-ish, but it works!
12. Slide the washer over the two bends to hold it in place. We know, it looks a little b

13. The completed slider/tab assembly. Our wire came pre-bent, though some may not. Sube Sports will pre-bend the wire for you upon request.
13. The completed slider/tab assembly. Our wire came pre-bent, though some may not. Sube
14. Another picture of our awesome seats. I couldn't resist.
15. Time to bolt the slider assembly to the seat. Start off by getting a couple threads on the allen bolt to catch, and get the other 3 started before you tighten.
15. Time to bolt the slider assembly to the seat. Start off by getting a couple threads o

16. You'll have to push the slider down to give you access to the other hole in the seat. Line up the bracket and tighten.
16. You'll have to push the slider down to give you access to the other hole in the seat.
17. Install the last bolt and tighten.
18. Almost done. Installation of the Cobra Daytona Sport is as simple as removing the stock seats.
18. Almost done. Installation of the Cobra Daytona Sport is as simple as removing the sto

19. After bolting the seats in, go ahead and tighten the allen bolts that are holding the tabs onto the sliders.
19. After bolting the seats in, go ahead and tighten the allen bolts that are holding the
20. It doesn't look like the harness will fit through the harness holes in the seat, but they do. The harness must be folded once over to slip through. Do not force it!
20. It doesn't look like the harness will fit through the harness holes in the seat, but t
21. The Schroth Rallye harnesses bolt in the factory locations and utilize the stock OEM hardware.
21. The Schroth Rallye harnesses bolt in the factory locations and utilize the stock OEM h

22. The tailstraps bolt in to where the rear passenger safety belts normally go. Refer to the factory Helms manual for rear seat removal.
22. The tailstraps bolt in to where the rear passenger safety belts normally go. Refer to
23. Finished! The seats and harness combo definitely improve driver support in high speed turns. They also give our Integra's interior a more purposeful look.
23. Finished! The seats and harness combo definitely improve driver support in high speed
24. Check back for a performance evaluation sometime in August.